back
spraygunworld
wood
Ask@SprayGunWorld.com
fuji
line

logo
model 7

NOTE: XPC & XT2 SERIES PARTS DO ARE NOT INTERCHANGEABLE

Fuji Tip Sets for New XPC & G-XPC2
2024
Size #2 .7 mm (.028") SUPER FINE OUTPUT  
$56.40
2024
Size # 3 - 1.0 mm (.039") FINE TO MEDIUM OUTPUT  
$56.40
line
2037
Size # 4 - 1.4mm (.055") MEDIUM OUTPUT
$ 56.40
line
fuji aircap
Size #  5 - 1.8mm (.070") HIGH OUTPUT
$ 56.40
line
2038
Size #  6 - 2.2mm (.086") EXTRA HIGH OUTPUT
Texture Coating
$ 56.40
line
  spacer
Standard Fuji Tip Sets for XT2 & GT-X2
2024
Size # 3 - 1.0 mm (.039") FINE TO MEDIUM OUTPUT  
$56.40
line
2037
Size # 4 - 1.4mm (.055") MEDIUM OUTPUT
$56.40
line
fuji aircap
Size #  5 - 1.8mm (.070") HIGH OUTPUT
$56.40
line
2038
Size #  6 - 2.2mm (.086") EXTRA HIGH OUTPUT
Texture Coating
$56.40
line
  spacer

 

 

The fluid jet and needle MUST always match exactly. However, the spraycap/air nozzle may be one size up or down from the norm. The sizes No.3 and 4 setups are both ideal for all fine finishing. 3 different setups are available as accessories. Generally speaking, the quality of atomization and finish suffers as you go to the largest size setups (No.5 and 6). Please note that the chart offers you a starting point only as to the setup size to be used. The best way to decide is by experimentation. If you are using the No. 3 setup and wish to spray faster, wetter then switch to No. 4.

IF YOU DO NOT INTEND ON SPRAYING WALLS & CEILINGS THEN THE ONLY TWO SETUPS YOU WOULD EVER NEED WOULD BE THE #3 AND THE #4.  

Size # 2 - 0.7 mm (.028") SUPER FINE OUTPUT

Most ‘fine-finishing’. For Automotive Waterbase Base Coats, STAINS, Dyes, Tanning Solutions, thin "Water type" liquids.

*Size # 3 - 1.0 mm (.039") FINE TO MEDIUM OUTPUT
Our favorite for Cabinet makers

Most ‘fine-finishing’. WATER-BASED LACQUERS, NITROCELLULOSE LACQUERS, SEALERS, CELLULOSE, ACRYLICS, SYNTHETICS, POLYURETHANE, STAINS, VARNISH, GLITTER PAINTS, PRIMERS. Please note thicker material must be thinned as much as 30%. Thinning beyond manufacturers specs should not affect finish quality if done properly. No latex and house enamels with this tip.

Size # 4 - 1.4mm (.055") MEDIUM OUTPUT

Similar to No. 3 but more coverage. Especially suitable for AUTOMOTIVE ENAMELS, NITROCELLULOSE LACQUER, CATALYZED LACQUERS and LATEX where finer finish is required such as louver doors, trim, cabinets (see section above about Latex). Also good for VARNISHES and OIL-BASED PAINTS. Latex paint must be thinned 20%-30%. We recommend floetro, extender or Penetrol.

Size #  5 - 1.8mm (.070") HIGH OUTPUT

Larger surfaces, thick layers, spotted effects. SEALERS, VARNISH, POLYURETHANE, OIL BASE PAINTS, ENAMELS, EPOXY, PLASTIC, ADHESIVES, FLOOR PAVING PAINTS, LATEX (on walls) SPLATTER PAINTS, MULTI-FLECK ETC.

Size #  6 - 2.2mm (.086") EXTRA HIGH OUTPUT

Very heavy flows, fast coverage. STONE FINISH PAINTS, TEXTURE COATING, INDUSTRIAL PRIMERS, LATEX (on walls, ceilings) ETC.

 

 

line
COMPLETE OUTFITS

mity GT-XT2

 

 

 

 

 

space

 


We also have a wide selection of quality tools for the Professional and Serious Hobbyist at www.SprayGunWorld.com.



 
SprayGunWorld