Stewart Systems is great because it is a Waterbased System so you do not have to worry about harmful isocyanides. Typical Application uses a 1.3mm Gravity Feed Spray Gun or a 1.0 Pressure Feed System.

Here are some recomendations for Stewart Systems Paints

Smaller Compressor
Low 3CFM
Standard 110v Compressor
Low 5-7 CFM
8CFM COMPRESSOR or Larger 220v Compressor No Compressor
Turbine 4 Stage

Mini Spray Gun w/ Larger Cup
While it is recommended to get access to a larger compressor, if you don't mind working with a 6"-7" fan pattern this will get the same quality results are larger spray guns at 10"-12" fans


For decent results we suggest a 4 or 5 stage turbine only. For portability turbines are terrific, turbines typically weigh in at 20 lbs while, for example, a compressor we like for conventional HVLP starts at 38lbs. wb

Gun Only (Suggested 1.5)

Complete Case as Shown

Pressure Pot Setup


We Recommend
Sprays Better than the Finishline III and uses the same fluid setting as in Stewart Systems Instructions.
The Low CFM Gun Leader


This is our favorite HVLP Kit for those who want low overspray HVLP.


See also with Disposable Cups


Need Speed for Larger Aircraft

New Reduced Pressure - this is our favorite Kit for those who want a little finer finish over HLVP and do not have HVLP restrctions in their area.


"Great Setup!...Thanks for your answers and recommendations. I received the SXK1 and flex cup kit from you last week. Just shot an aircraft belly and wings in primer and silver. The gun is excellent and the cup system is unbelievably easy to use. I’m thrilled with the way it works. I was lying on my back, shooting upside down onto the bottom of this plane – it works beautifully! Mix is easy and clean-up so simple. (I just throw the cup away and clean up the business end of the gun.) It’s a snap! I’m sold."



Our Least Expensive Setup, Compares to Finishline III

r Series

Gun Only

d overspray was a problem. A new technology was introduced: High-volume, Low-pressure (HVLP). The pressure used in these systems to atomize the paint is much lower (3-5psi). The paint cup is pressurized forcing material to the nozzle. As a result, the overspray problem is minimized. Most of the paint actually adheres to the surface being painted instead of bouncing off and collecting elsewhere. To achieve this advantage a HVLP spray gun must be machined to a higher degree than an ordinary spray gun. Hence the higher cost of very good HVLP guns. The HVLP spray gun is designed to gather the air inside the gun and send it downstream with as little pressure drop as possible. This means careful machining must be carried out to reduce turbulence that impedes airflow. In older pressure guns if a passage was too small you simply increased the pressure and solved the problem. That means conventional spray guns do not have to be machined to exact specifications.

Advantages of the HVLP system. 1) overspray is reduced dramatically. That means a saving in coatings typically of about 35-50%. 2) HVLP systems enable the beginning painter to achieve a professional looking finish. They are easier to use than conventional spray outfits. Individuals who have experience painting with conventional spray outfits will have to learn the different techniques required to use HVLP systems. HVLP systems expend heavier amounts of material than conventional guns. This, of course, means different techniques.

Until Now. Now there is an option of Reduced Pressure Guns, these guns act similar to standard conventional guns and therefore no new learning technique is necessary. However, with the incorporatino of modern technology they too produce lower overspray levels similar to HVLP. They are very popular among older painters.

This is a top low cost choice.


Gun Only

Master Case as Shown Above


Our Finest USA GUN Period
Superior to the Mach 1 and FLG 3 Gauranteed!

CPR by CA Technologies



Equal to but a better deal than the Mach 1 - Why get this one? it will work on as little as 6cfm if necessary





Please get SGW Package with hose extention and 1.0 nozzle set for optimum finish quality


* Cockpit - Mini guns are great for Cockpits and tight areas. We also carry 4 oz and 12 oz cups for your full size spray Guns and full size guns can use 6-9oz disposables by 3M or DeVilbiss - line


Have Fun!